Skip to content
Gloved installer assembles a hydronic heating manifold with circulator pumps on a workshop bench

Pricing tools

HVAC Pricing Guide for Contractors (2026): How to Price Service and Installs

By· Founder, Made For BuildersReviewed

Check the margin on an HVAC job before you quote it

Enter the job price, equipment and parts cost, labor cost, the hours on the job and overhead as a percentage of direct cost. The calculator returns net profit, true margin, true markup and profit per hour, so you can compare a service call with an install. It runs in your browser and sends nothing.

The job numbers
$

What you charge for the whole job, before tax.

$

Everything you buy for this job.

$

What the labor costs you, including your own time.

h

Total hours spent, not just the billable ones.

12 %

Truck, insurance, office and admin, allocated as a % of direct cost.

Margin and markup are not the same thing. Margin is profit as a share of the price; markup is profit as a share of the cost. A 30% markup leaves only a 23% margin. Most contractors confuse the two and undercharge without realizing it.
Your true profit on this job
Net profit$2,680what you actually keep after covering cost and overhead
True margin17.9 %
True markup21.8 %
Total cost incl. overhead$12,320
Profit per hour$22
Total cost$12,320
Profit$2,680

Directional model. The common mistake is ignoring overhead and treating markup as margin. Allocate your real overhead on top of direct cost: true profit is almost always lower than the quote makes it look.

HVAC pricing inputs at a glance

BLS publishes what HVAC technicians are paid and what employers spend on benefits. It does not publish what contractors charge for a service call or an install, and we found no primary source that does. The price has to be built from your own labor, equipment, overhead and margin.

What you can look up and what you have to measure
InputFigureSource and date
Median wage, HVAC mechanics and installers$61,010 a year (about $29.33 an hour at 2,080 hours)BLS Occupational Outlook Handbook, May 2025
Wage rangeLowest 10%: under $40,050. Highest 10%: over $95,210BLS Occupational Outlook Handbook, May 2025
Benefits share of employer compensation cost30.0% (private industry, all occupations)BLS Employer Costs for Employee Compensation, June 2026
Typical service call or install priceNo reliable sourceNot published by BLS or any primary source we found
Equipment cost, overhead and task timesYour supplier quotes and booksMeasure, do not copy
The hourly equivalent is our arithmetic: $61,010 divided by 2,080 hours.

How to set an HVAC price: the formula behind the calculator

Price = (labor hours x loaded labor cost per billable hour + equipment and parts) x (1 + overhead %) / (1 - target margin). The calculator works it in reverse: type the price you plan to quote and it shows the profit, margin, markup and profit per hour that price leaves.

The same formula covers a no-cool call and a full system replacement. What changes is the weight of each input: service work is mostly labor, installs are mostly equipment. That is why a single margin target for both often prices one of them wrong.

Cost of labor: wage, burden and billable hours

According to the BLS, the median HVAC technician wage was $61,010 a year in May 2025, about $29.33 an hour. With the all-industry benefits share of 30.0% and 6 billable hours out of 8 as an example, one billable hour of a median-wage technician costs about $55.87.

The BLS Occupational Outlook Handbook reports that the median annual wage for heating, air conditioning and refrigeration mechanics and installers was $61,010 in May 2025, with the lowest 10% under $40,050 and the highest 10% over $95,210. Use your own payroll; the median is a reference for hiring and for checking your pay.

The BLS Employer Costs for Employee Compensation release reports that private-industry benefit costs were 30.0% of employer compensation in June 2026. As an example, $29.33 / 0.70 = $41.90 per paid hour. If technicians bill 6 of every 8 paid hours (use your own dispatch data), the cost per billable hour is $41.90 x 8 / 6 = $55.87.

Billable hours move with the season. The BLS notes that HVAC technicians "may be on call for emergencies and sometimes work overtime or irregular schedules during peak heating and cooling seasons." Overtime raises the labor cost of peak-season jobs, and slow months lower billable hours. Price on a full-year average, and treat after-hours work as a separate line with its own cost.

Pair of pressure gauges on insulated piping in a building mechanical room

Overhead on service work and on installs

Overhead covers trucks, insurance, licensing, office, dispatch, software, marketing and warranty callbacks. The calculator applies it as a percentage of direct cost. Because installs carry large equipment costs, a single percentage can load too much overhead on an install or too little on a service call, so check both.

  • Service vans, fuel, maintenance and stocked parts.
  • Liability insurance, bonds, contractor and EPA certification costs (see HVAC license).
  • Dispatchers, CSRs, office and software.
  • Marketing and lead costs, including per-lead fees or commissions on closed jobs (compare sources in HVAC leads).
  • Warranty labor and callbacks you do not bill.

If most of your overhead follows technician hours rather than equipment dollars, a lower overhead percentage on installs and a higher one on service reflects it better. That is a choice for your books; the examples below use 25% on service and 15% on an install to show the effect.

Margin vs markup on HVAC equipment and labor

Margin is profit divided by price; markup is profit divided by cost. A 30% markup on equipment leaves a 23.1% margin, not 30%. On an install where equipment is most of the cost, mixing up the two changes the profit by hundreds of dollars per job.

Markup needed for a target margin (arithmetic, not a benchmark)
Target marginDivide cost byEquivalent markup on cost
20%0.8025.0%
25%0.7533.3%
30%0.7042.9%
35%0.6553.8%
40%0.6066.7%

No primary source publishes an average HVAC margin, so this guide does not quote one. The calculator flags any margin under 15% as thin. To convert between the two directly, use the markup vs margin calculator on the plumbing price book page; the math is the same for any trade.

Worked examples: a service call and an install

Example only, with round inputs: a 1.5-hour repair with $45 of parts priced at $250 leaves a 35.5% margin and $59.17 profit per hour. For installs, start from real prices: in 1,088 heat pump HVAC projects in Silicon Valley Clean Energy's rebate program (2022-2024), total project cost ran from $8,560 to $44,900, with a median of $18,965 before rebates.

Service repair: calculator inputs and results (illustrative, not market prices)
Service repair
Price$250
Equipment and parts$45
Labor cost ($55.87 per billable hour)$84 (1.5 h)
Overhead on direct cost25%
Total cost with overhead$161.25
Net profit$88.75
True margin35.5%
True markup55.0%
Profit per hour$59.17
Enter these inputs in the calculator above to reproduce the results.
Heat pump HVAC installs: total project cost in one rebate program
Project costTotal, before rebates
Low$8,560
Median$18,965
High$44,900
Silicon Valley Clean Energy (California), 1,088 residential projects in its Home Rebates Program, 2022-2024, before rebates or tax credits; low and high remove 2% of outliers. One local program, not a national average.

Use the range to test your own install quotes, not to set them. The arithmetic: every $1,000 of equipment, labor or overhead you add to a job lowers the margin by 11.7 points at the low price ($8,560), 5.3 points at the median ($18,965) and 2.2 points at the high price ($44,900). Enter your own equipment quote, labor hours and overhead in the calculator above to see where your install lands.

Installs and service calls earn differently. Equipment dollars can carry profit without using labor time, so an install can have a lower margin and a higher profit per technician hour than a repair. A price list needs both views: margin protects you against cost surprises, profit per hour tells you which work earns more per technician hour.

Flat rate vs time and materials for HVAC

Flat rate fits repeat service and repair tasks that you have timed often: the customer approves one price and you carry the time risk. Time and materials fits diagnosis-heavy work you cannot scope. Installs are usually quoted per job from a site visit, using the same cost-plus-margin formula.

  • Diagnostic or service call fee: priced as its own line from book time and the loaded cost of the visit, including drive time.
  • Flat rate repairs: one line per repeat task (capacitor, contactor, motor and so on), priced from your own average times.
  • Installs and replacements: quoted per job from equipment quotes, labor hours, permits and overhead.
  • Maintenance agreements: priced on the visits and parts discount they commit you to, checked like any other job.

How a flat rate behaves when a task overruns its book time is worked through in Flat Rate Pricing for Plumbers; the arithmetic is the same for HVAC. Electrical contractors face the same choice: see the electrical pricing guide.

Building the HVAC price list and using it in the field

List your most common service tasks and install types, price each from the formula and check it in the calculator. Then record actual hours and parts on every job, compare them with the list each quarter and reprice the lines that drift, especially before each peak season.

  1. Pull a year of invoices

    List the service tasks and install types you do most often.

  2. Time each task

    Use average times from your own dispatch records, not the fastest technician.

  3. Cost equipment and parts

    Use current distributor pricing and date it.

  4. Price and check

    Apply overhead and margin, then run each line through the calculator.

  5. Offer options

    Repair, replace and upgrade options for the same problem let the customer choose.

  6. Review before each season

    Update equipment costs and task times before summer and winter peaks.

If a job comes from a channel that charges per closed job, add that charge to the job's cost before you check the margin. In the Partner Program it is 20% of the labor on service and repair jobs and 15% of the net on installations and replacements. Installation net: the invoice excluding sales tax, minus the documented cost of materials, equipment and permits. Details on the commission page.

Your prices are set. Now fill the schedule: partners get the calls from their area. One partner per trade per area. No setup fee, no monthly fee, no pay-per-lead. Made For Builders is not a contractor.

HVAC pricing FAQ

How do HVAC contractors calculate their prices?

From cost upward: labor hours times loaded labor cost per billable hour, plus equipment and parts, plus overhead, divided by one minus the target margin. The calculator on this page checks the result for any job.

Should HVAC service and installs have the same margin?

Not necessarily. In the example on this page the install earns a lower margin but more profit per hour because equipment carries profit without using labor time. Set targets for each type of work from your own numbers.

What is a good margin for an HVAC business?

No primary source publishes a reliable HVAC average, so this guide does not give one. Set it from what you need to cover callbacks, slow months and growth. The calculator marks anything under 15% as thin.

How should I price an HVAC service call?

Treat it as its own line: book time for the visit and diagnosis, including drive time, at your loaded cost per billable hour, plus overhead and margin. Repairs found on the call are then priced from the price list.

Is markup on equipment the same as margin?

No. A 30% markup on equipment cost leaves a 23.1% margin on the price. To reach a 30% margin you need a 42.9% markup.

Sources and method

Wage, benefit and schedule information comes from the BLS pages below, read on 9 November 2026. Install price ranges come from the Silicon Valley Clean Energy table below, read on 10 November 2026. Other job prices, task times and costs on this page are illustrative examples with round inputs, labelled as such. The hourly wage equivalent and loaded labor cost are our arithmetic on the BLS figures.

Next steps

Where to go from here

  • Your trade

    How the Partner Program works for your trade: the jobs, the licensing check and how commission is paid.

    See your trade
  • Run your numbers

    A free calculator to check the margin on a job before you price it.

    Open the calculator
  • Pricing tools

    Calculators for rates, margins and job prices.

    All tools
  • How the Partner Program works

    We build and run a local brand for your trade in your area. The calls ring on your phone and you pay commission only on jobs you close.

    See the Partner Program
  • Apply to the Partner Program

    Calls from your own area under a local brand. Commission only on closed jobs.

    Apply

Last reviewed: